Getting Started with Plumbing Basics When Installing a Bathtub
Getting Started with Plumbing Basics When Installing a Bathtub
Blog Article
The author is making a few good points regarding Installing A Bathtub in general in the article which follows.
Installing a bath tub isn't precisely rocket science, yet it does require solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately challenging task. If the old tub is conveniently available, the job can move quickly; if you need to open a wall to get rid of the old tub and also place the new bath tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will need an assistant to move out the old bathtub as well as set in the new one. Make sure you have qualified yourself for the work as well as fit attempting it. Rather than hiring a service provider to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you begin. Possibilities are you may require a professional plumber to make tube links.
This short article will aid you set up a brand-new tub in your washroom if you have actually already acquired a new bathtub as well as do not need to transform the setup of your previous supply of water pipes.
Your tools as well as material list should comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The process of removing the existing faucets can be quite problematic due to the restricted gain access to that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer provided backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The previous type must be linked to the faucet finishes initially, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bath tub
Utilizing the two wood boards under its feet, position the tub in the called for position. The wood boards are valuable in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub until the spirit level reads degree.
To install faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water and check all joints and new pipework for leaks as well as tighten them if essential. Load the bath tub and also examine the overflow outlet and the normal electrical outlet for leaks.
Finally, repair the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the tub ought to wait until the bath tub has actually been utilized at the very least once as this will certainly settle it right into its final placement.
Getting ready for the Setup
First of all, the sustaining framework provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a rigid seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, causing issues with wetness and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are sold in tubes and cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to allow for the motion experienced when the tub is in use. The sealant can crack rather very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I was introduced to that report on Tools You Need to Install a New Bathtub through someone on another site. Liked our content? Please share it. Help somebody else discover it. Thanks for taking the time to read it.
Book An Estimate Now Report this page